Replacing uPVC Window Handles
It is simple to change the handles on upvc windows. It is important to ensure that the new handle is fitted into the spindle cutout in the window mechanism.
If the steps below are followed properly the cockspur handle will be able to fit into most windows. The key is the step in the height of the handle.
What to Look For
As time passes, uPVC handles on many windows in the UK can start to show signs wear and tear. When this occurs, the window handle can become loose or difficult to operate, which makes it essential to replace it. This is a relatively easy task that is achievable by anyone who is comfortable with basic hand tools.
The first step is to ensure that the handle is firmly fixed to the window frame and is in a position that is open. The next step is to find the fixing pins or screws that hold the handle in the position it is in. They are typically located on the inside of the handle. They can be removed with the screwdriver and pliers.
When the handle has become loose and sagging, gently pull it back from its hinges. It is then necessary to find a new handle with the same design and size. This can be accomplished in an online store or in a DIY store. The procedure should take just five minutes, and you will need a screwdriver is all you need.
upvc replacement door handles to take into consideration when replacing a uPVC window handle is its step height. This is the distance from the base of the handle until it sits on the window frame. This is usually an average measurement, but it is crucial to determine the step height of your existing handle before purchasing a new one.
There are a variety of sizes based on the type of handle. Inline handles can be found for uPVC window with lug centres of 31mm, while cockspur handles come with centers of lugs of 43mm. Tilt-and-turn handles are commonly found on uPVC Windows. They feature a unique design that allows the window to be tilted for ventilation and then rotated to fully open the window.
The most common cause of breakage in uPVC handles is that they crack inside rather than breaking off from the base section. This makes them difficult to open and therefore it is essential to ensure that the replacement handle you buy has the same length of spindle as your existing one.
Remove the old Handle
If the handles on your windows are damaged or incorrectly installed, they could cause double-glazed windows to close and open incorrectly. They could even become stuck. This could be due to a number of factors, such as general wear and tear on the handle or corrosion. In these situations it is essential to find replacement upvc window handles immediately to prevent further damage and loss of function.
One of the first things to do when replacing upvc window handles is to remove the old handle from the window. To do this, begin by removing the screw that is covered when the handle is in the closed position. Once you have removed the screw, you are able to remove the handle. It is possible to make the task easier by using an electric screwdriver.
Be aware that screws could be hidden in caps made of plastic. It is recommended to remove the covers using the help of a Stanley knife. After you have removed the old handle, you'll have to examine the square cutout on the base to ensure that the new handle you choose for the window lock is compatible. It is crucial to measure the length of the spindle on the handle that was used and compare it to the dimensions of the window mechanism spindle cutout.
There are three types of Upvc handles: Espag handles with a central screw that can be turned right or left and Cranked handles with two screws, and Spade handles which are made of flat arms and can be used either side of the windows made of upvc. It is easy to replace the handle after you've identified one that is suitable. Simply screw it into place, and ensure that the spindle is correctly inserted into the lock mechanism. Once that is done, it should be tightened to the window frame and the replacement window handles made of upvc must be secure.
Measure the Spindle
If you're replacing a Upvc window handle that has fallen off, it's due to the spindle that holds it in place is loose or damaged. In certain situations, you can tighten the spindle using pin or screw. In certain situations, it may be necessary to replace the handle. There are a variety of handles made of upvc. They include espagnolette handles inline, cockspur handles, and tilt and turn handles. Each kind has a distinct method for installing and replacing the handle.
Before you purchase a new handle, it is essential to know the dimensions of the one you have. This will ensure that the handle fits the window correctly and will be the right size. Fortunately, all handles follow industry standard sizing so it's fairly easy to find the correct size.
To measure the size of your handle first remove it from the window by turning it to an open position. You should be able to determine the dimensions of the pin or screw that secures the handle. Then, use a ruler or tape measure to determine the length of the spindle. Once you know the length of the spindle, you can purchase a replacement one that is exactly the same size.
The step height of a upvc window handle is also a factor to consider when buying an alternative. The step height is the distance from the base of the handle until where it rests on the frame. This usually is around 21mm or 9mm in aluminum and uPVC. To ensure that the new handle will work the gap, drop something into the gap to see how far it extends before it meets an obstruction.
Cockspur handles usually have different backset heights depending on the style of window they are installed in. Inline Espag handles come with the standard height of 43mm centre to centre (2 fixing points). Cockspur handles have different backsets, based on the type of window they are located in. This is because they feature an extension spur that extends from the handle and is secured over a cockspur wedge striker.
Install the New Handle
Once you've selected the new handle, align it carefully with the screw holes on the door. Secure it using the screws supplied. If you're also replacing the latch lever the lever can be mounted similarly to the main door handle. Finally, reattach the door trim to hide the mounting screws and close the job.
Tips: To remove a metal head from a wooden wedge, place the handle on the floor so that its wide end is on the floor. Then use an hammer and tap the narrow end. Be careful not to scratch the handle or spindle.